A mixing paint tank is an essential tool for any professional painter or paint contractor. It allows you to efficiently mix large quantities of paint so you can keep your painting projects for a long time. Here is an in-depth look at paint mixing tanks, how to use them properly, and some important safety tips.
A paint tank, sometimes called a paint pot, is a container designed specifically for holding, mixing, and feeding paint to a paint spray gun. Paint pot ideal for large area spraying such as buses, trucks, and vans, fences, interior/exterior wall, garage, and other big projects with high efficiency.
It has an airtight lid and is connected to the spray gun via a hose. Paint is poured into the tank, then pressurized air is added. This air agitates and mixes the paint, keeping it properly blended while spraying. The constant air pressure also forces the paint up through the paint hose and out of the spray gun nozzle.
The key advantage to using a paint tank over just pouring paint directly into a spray gun is uniform mixing. With a tank, the paint stays well-mixed and thinned as you spray. Without a tank, paint components can separate and clog the spray gun. A tank also holds more paint than a spray gun cup, allowing longer spraying sessions before refilling.
When getting started, fill the paint tank about three quarters full with the paint you'll be spraying. Start by making sure your paint tank is clean. Any dried paint or debris left over from previous use can clog up the hose and spray nozzle. Strain the paint through a paint filter or mesh bag first to remove any clumps or debris. Latex and oil-based paints both work well in pressure tanks. Screw the lid tightly onto the tank and make sure all seals are properly in place.
Next, securely close and seal the tank's lid. Attach the air hose from your compressor to the tank's air inlet, and attach the paint hose from the tank to your spray gun.
Slowly increase the air pressure in the tank to between 8 to 15 PSI. This will vary based on the viscosity and type of paint. Thicker paints require more pressure to atomize properly. Activate the spray gun briefly to ensure paint is flowing smoothly. Adjust the pressure up or down as needed until the paint is spraying an even mist.
When using a mixing tank for latex paint, be very careful not to overmix. Latex has a "pot life" and excessive blending will ruin the paint. Mix just long enough to combine, usually 5-10 minutes. You'll know it's overmixed if the paint starts bubbling and changes texture. Then it's unusable. Oil-based paints and primers can handle longer mixing duration. But stick to the minimum time needed to fully incorporate all components.
Turn on the tank and allow it to run for a few seconds to prime the pump and hose. Priming the tank helps prevent paint spraying everywhere when you pull the trigger for the first time.
As you spray, keep an eye on the paint level inside the tank. When it gets low, turn off the compressor and carefully refill. Remember to strain any new paint before adding to the tank. Don't overfill the tank, as air space is needed for mixing and stirring the paint.
Safely using paint mixing tanks
Place it on a level, steady surface so it doesn't tip while operating. The spinning action will make it "walk" if not stable.
Turn off before adding or moving the tank.
Never exceed the maximum working pressure rating listed for your tank. Over-pressurization can dangerously damage the tank.
Periodically check fittings and hoses for wear. Replace any damaged pieces.
Prevent dirt and debris from getting into the tank. Always strain paint before adding to the tank.
Use caution when refilling. Turn off the air supply and release pressure before opening the lid.
Clean the tank thoroughly after each use. Residual dried paint can clog hoses, fittings, and spray nozzles.
AEROPRO A8312 paint tank has twin set of hoses permits easy movement and operation of spray gun. Pressure spray gun equipped with pressure gauge and fluid pressure regulator for accurate settings. Excellent for large areas such as buses, tuck and vans. Sturdy construction and compact design makes these products the ideal choice for both amateur and professional.
With proper setup and safe handling habits, a paint tank can make spray painting much easier. The ability to presurize and continually mix paint allows you to focus on controlling the spray gun rather than stopping to mix paint. Just maintain the tank and components well to ensure years of reliable service. Let us know if you have any other paint tank questions!
Model: A8312
Paint Capacity:10L
Working Pressure:1.4-2.1bar
Paint output:1/4"
Dimension:283x283x383mm
View More About AEROPRO Paint Tanks.
If you need product quotation service, please contact: sales@aeroprotools.com