Staining your deck can protect and beautify the wood, helping it last for years. Airless sprayers also provide better penetration into the wood grain for long-lasting protection. When taking on a deck staining project with an airless sprayer, follow these key tips.
Choosing Your Materials
When prepping to stain your deck with an airless sprayer, choose your products carefully for best results. Opt for a specially formulated deck stain rather than a standard exterior stain. Deck stains contain UV blockers, water repellents, and mold/mildew inhibitors designed to protect exterior wood. For airless spray application, select a deck stain formulated to spray on without thinning. Oil-based or water-based stains will both work well, so choose the finish and color you prefer.
Use the Right Sprayer and Tip
For staining standard residential decks, a compact electric airless sprayer with around 0.5 gallons per minute (GPM) flow rate is ideal. Keep pressure at the lowest needed for good atomization, around 1200 PSI for thinning stains.
When selecting spray tip sizes, consider the thickness of your deck stain. Semi-transparent and solid color stains call for fine finish low pressure tips around .011”to .013”size, ability to spray efficiently at a lower pressure.
Preparing Your Deck
Use painters tape, cloth tarps or plastic sheeting secured with weights to cover any landscaping, patios, siding or windows near the project area. This will protect from accidental overspray getting where it’s not intended. Drop cloths underneath can catch drips and spills. Remove downspouts during staining if applicable.
Check for surface flaws like cracks, splinters and protruding nails. Sand rough areas, then vacuum up the dust. Fill small gaps with exterior-rated wood putty, allow to dry completely, then sand flush. Wipe the entire deck with a tack cloth before spraying on new stain.
Spraying On Your Finish
To avoid lap marks, always maintain a wet edge by applying stain on a smooth, continuous motion and working in rectangular sections. Plan your application path beforehand by partitioning off your deck into even work areas.
Move sprayer at a steady, straight rate parallel to the deck boards. Periodically pivot your torso rather than overextending your arms. Apply stain uniformly to saturation and back-brush spots showing lap marks, drips or thin coverage. However, avoid excess wetting.
Work during the shade and out of direct sunlight whenever possible, as this helps the stain dry properly. Do not spray in windy conditions that can disrupt the spray pattern and cause overspray issues.
Let Sections Dry Before Adding More
Allow each section ample drying time before adding another layer or reopening to traffic. Adding too much stain without drying in between can lead to a gummy, shiny finish and poor adhesion. Drying times range from 2-6 hours between coats in ideal weather conditions.
Once fully cured, the deck stain should appear evenly saturated without shiny spots for a professional look that highlights the beauty of the wood grain. Annually inspecting your deck and reapplying stain as needed will keep it looking its best.
Taking the proper preparatory steps and utilizing AEROPRO AP8626 airless paint sprayer allows for efficient, quality staining outcomes. Compact structure, light weight, high productive sprayer for DIY and Tradesman professional use.
Despite its lightweight form factor, the AP8626 packs a punch with 3000 PSI max pressure and a 1.0 HP motor power. With the 821 airless spray gun and 7.6m high pressure air hose for easy mobility when painting deck. This sprayer can handle thick stains as well as paints and clears to coat your deck, fences and more with a protective finish.
Perfect for small to medium projects, indoor and outdoor DIY projects like interior walls, ceilings, exterior siding, fences, decks, sheds,garages etc. Suitable for various coating types: water-based paints, oil-based paints, latex, enamels, lacquers, acrylic, varnishes, primers, stains, preservatives and other non-abrasive materials.
Voltage | 220V/50Hz, 110V/60Hz |
Motor Size | 1.0HP, 750W |
Max pressure | 3000psi |
Standard Nozzle Size | 517(0.017") |
Length of High Pressure Hose | 7.6m |
Max.Pressure for the Hose | 83Mpa |
Flow Rate | 1.2L/Min |
Net Weight | 7.0Kgs, 15.4Lbs |
AEROPRO has quickly risen to become an unrivaled global producer of air-powered devices including air tools, air spray gun, air nailer, airless paint sprayer, and etc.
AEROPRO seeks independent sales agent to represent and market our industry-leading pneumatic tools. We support OEM, ODM, OBM customization, small order quantity is acceptable and samples are available.
Make any cooperation possible. Any services related to the product, inquire with us now! Sales@Aeroprotools.Com